Blogs
Looking for the old Kontakan site? It has been moved to Berkada.com.
on July 29, 2022
Today, we are going to talk about three issues that come up quite frequently and demonstrate the most effective method for resolving those issues or preventing future occurrences of those issues. Today, we are going to talk about three issues that come up quite frequently. Carry out the modifications that are required:Move more slowly and take your time while you are cutting the tube. This will ensure a clean cut. If the issue continues to occur, you might want to experiment with a different blade that is not only more narrow but also has a finer grit. If you're having trouble finding a solution, this is something to think about as a potential option.
Burring is the very last stage of the cutting process, and it is accomplished with the assistance of a tool that is also called a burr. Burring is also known as "burring" the edges of the cut. It might be either one of them, or it might be both of them at the same time. By utilizing a weight or a clamp, you can make sure that there is very little movement throughout the entirety of the cutting process. This will ensure a clean cut. This will make it possible for you to ensure that there is very little room for error on your end.
An unsafe level of overheating is frequently the result of an excessive amount of friction, which can be extremely hazardous. This kind of overheating can occur for a number of different reasons.
Take the temperature down one or two notches and try again. Due to the extremely high tensile strength that it possesses, aramid is a material that is extremely challenging to cut. The possession of it will be advantageous, despite the fact that there is a possibility that it will not be the benefit that provides the most significant advantages.
The issues that have been listed above are some of the most common complications that can occur when cutting carbon fiber. Cutting carbon fiber, on the other hand, can present you with a wide variety of additional challenges as well. If you are having issues, please do not be reluctant to get in touch with us; we are here to assist you in any way that we possibly can. In the event that you are having problems, please do not be reluctant to get in touch with us.
To get things rolling, we would like to extend our deepest and most heartfelt gratitude to all of our closest friends who have been an indispensible part of the process of developing the technologies that are described in the paragraphs that follow:
Aleksey Lantsov was the one who suggested that we build models of indoor RC planes out of 3k carbon fiber tube rods for the frame and cover them with a thin layer of Mylar plastic foil. This was Aleksey's idea. It was Aleksey Lantsev who came up with the concept that we ultimately decided to go with.
This post will discuss the overarching principle that Kimmo bases his life on, and an explanation of why he does so will be provided at the end of the post. As can be seen, there are no challenges whatsoever involved in the process of shaping carbon rod into various configurations. In order to successfully complete this project, you will only require carbon fiber round tube filament, epoxy resin, and silicone tube with the appropriate diameter. This subsequent step will take place after the previous step, which consists of dipping the carbon filament in the resin.5 millimeters. Because of this, it is more difficult to pull, but doing so will result in the production of a length of shaped rod that, due to its virtually limitless potential, has virtually an infinite number of applications.
In the present, we are only able to manufacture them up to a length of one meter; however, technology unquestionably enables us to manufacture items that are significantly longer than this. After the resin has hardened, any attempt to remold the material into a different shape by melting the resin with heat will, in the end, result in an essential loss of the material's strength in the parts that have been bent. This is because the resin will not be able to be reformed into its original shape. Because the carbon fibers should be able to freely slide against one another during the bending process, and because this is something that is only possible if the resin has not yet fully cured. This is the reason why this is the case. This is the explanation for why this occurred.
Collect all of the fibers into one large clump.
You are free to mold it into any form you like, but you must remember to keep it in that configuration until the resin has completely hardened.
We have decided to make use of heat shrink tubes in order to achieve the goal of fiber compression, and our reasoning behind this decision is as follows:The use of this method is associated with a number of benefits, some of which are listed below:1. Finding a way to reduce the amount of heat that is transferred to the resin, which is the material that is being worked on, is the most difficult aspect of the process of developing this technology. This is the material that is being worked on.
The tool that is required is a stencil.
Although it is not necessary for the groove to have a profile that is anything other than rectangular, having this shape is the one that is preferred. Utilizing a CNC routing miller is something that is strongly suggested to do in the process of milling a groove into a board. Because of this, the groove will always be cut to the highest possible standard. You will be able to achieve the highest possible level of precision that can be attained by a human being as a direct result of this.
Laser pointerThe tool that affords the highest level of precision that can be attained by a human being. Immediately, the temperature ought to be increased to the level that is appropriate. The significance of this cannot be overstated. In this specific situation, the most fruitful action that can be taken would be to make an investment in a heat gun that is able to provide precise temperature control. This would be the most productive action that can be taken.
Topics:
carbon fiber round tube
